what is the best way to simulate gesso on a canvas in ArtRage? with a rough texture or a layer with rough texture?( wood bark, scumbled paper)in overlay mode?
what is the best way to simulate gesso on a canvas in ArtRage? with a rough texture or a layer with rough texture?( wood bark, scumbled paper)in overlay mode?
https://forums.artrage.com/showthrea...low-Up-Example
I posted this a little while back. You can create your own textures for the canvas using a BW image which till translate into a tooth for the canvas. If you want it to look like gesso you can simulate the sweeping brush marks in BW and just make that your canvas. Could be anything in BW. But a gesso look is very do-able. This shows how it's loaded in, but you can of course use any BW image as the canvas, including the simulation of gesso brushed down. Experiment. It can be fun, I always thought.
Last edited by D Akey; 10-17-2018 at 04:24 AM.
"Not a bit is wasted and the best is yet to come. . ." -- remembered from a dream
thx dakey gone try this out
Hi Rondo. A couple things:
1) Are you using a desktop computer? I found that this feature doesn't exist in the version for some devices. For example it does not work on my Kindle Fire HDX. It definitely works on my Mac desktop. I seem to recall it also works on a Windows desktop version.
2) I noticed that because you were showing more of a value range than it should as a canvas. It looks more like you loaded it in as a layer or tracing image or something. See below for what it should look like. When I loaded your pic you attached for me to mess with, it loaded fine like gesso's white on white. See my attachment. But you really don't need to adjust it outside the canvas settings. However you can for extra finesse if you want. None the less, your original was working fine with the right settings.
3) I was not able to get rid of the tiling at full magnification even when your pic was the same as my new picture in AR. You can play with the settings once you get to the Canvas Settings. The way I got there was by right clicking the mouse when the cursor was somewhere in the AR canvas area. Then I loaded the image. The sliders are useful. USE LIGHTING (checked box). DO NOT USE METALLIC (off = no x in box). The sliders you can adjust to what looks good to your eye.
Let me know how it works for you. Your original BW image for the canvas should have worked. But I am also including another where it's more adjusted to high contrast. What that will give you is more of a canvas with 2 different depths - white will be uniformly flat. Yours with more value range will have more varying depths and that could be cool if you want a gesso look that has not been sanded.
PS. I used the chalk pastel tool with the magenta color selected for what you see below.
Last edited by D Akey; 10-17-2018 at 01:55 PM.
"Not a bit is wasted and the best is yet to come. . ." -- remembered from a dream
So Rondo, how did it work or can you even do it on your device or computer? You can ask for an expansion on the trick of it if you get hung up.
"Not a bit is wasted and the best is yet to come. . ." -- remembered from a dream
did not get the chance to test due to my health issues but I shall try it out when i'm able to, thx anyway sir
as far i found out is that the texture can be used in different ways,1)importing as a layer and put on multiply, 2) as a texture in canvas settings. Can also directly open the texture in ArtRage and create a another layer while putting again the texture in multiply. Can also be loaded as is. Run a Win10 machine I7-64bit.
Mind you that there are only a few tools that gone let you see the texture and indeed 1 of them is the chalk tool. but here again, possibilities are endless and ground to further trial and error
I hope you can understand what i'm writing here.
The only thing that bothers me is the fact that I see a seem in certain import methods? is this a normal behavior?